Gift presents: Scrap Buster Fall Pillow, sewing pattern

IMG_1189
 Gift presents: Scrap Buster Fall Pillow, sewing pattern
This is my favorite thing to do with my little scraps, and since its Scrap Buster month over at Sew, Mama, Sew, I made a quick tutorial so you can make your own. This pillow cover is 16" square with an envelope back & the design possibilities are endless! I added some pillows I’ve previously made with this same method at the end of this post. Happy Sewing!

You’ll Need:IMG_1151-11. Scraps, enough for the tree trunk and the leaves. Cutting your scraps into rectangles will make it easier to adhere them to the appliqué material.
2. Appliqué material: I use Heat' n Bond. You’ll need about 1/2 yard or more depending on how many leaves you want to make.
3. Material for the pillow front, cut to 17" x 17" square. I used lightweight canvas and prefer home weight material, but you could use anything.
4. Material for the back. Cut 1 rectangle 17"x 14" and cut 1 rectangle 17"x 10".
IMG_1153
Iron your fabric scraps onto your appliqué material according to the directions on the appliqué material. (press & hold the iron over each scrap for a few seconds, I use a very hot iron and find the appliqué material sticks better)
IMG_1157
Now with scissors cut out your trunk and leaf shapes. For the trunk I first draw the shape of the trunk on the back of the appliqué material so I get a nice shape, but for the leaves I just free cut as I go. And for reference the trunk on mine is 8" tall, and my leaves are all about 2.5" long and are 1.5" or so wide.
When you get all your leaves cut out, tear the backing appliqué paper off the leaves and trunk. I prefer to do this while plopped down in front of the TV cause it takes awhile. :) Or better yet enlist some help.
IMG_1160
Then you can arrange them how you want on your pillow front. Don’t place any within an 1.5" of the edges to leave room for sewing.
Once your design is how you like it, press with an iron over each spot for a few seconds making sure not to bump anything out of place. This will keep everything in place while you sew them on.
IMG_1164
Now you can sew either along the inside edges of your leaves, or you can do a zig zag stitch or blanket stitch around the edges if you prefer. I move my foot from leaf to leaf without cutting my strings so it goes faster, then go back and cut my strings at the end.
IMG_1165
To prepare your pillow back, fold one of the short edges of each pillow backing piece in 1/2" and press, then again 1/2" and press and sew to hide any raw edges. These will be the edges of the envelope back.
IMG_1171
Lay the backing pieces right sides down onto the pillow front over lapping the centers. I placed the smaller backing piece ( 10" x 17") down first on the pillow front, but I actually prefer to lay the larger pieces down first since it makes the cover easier to slip on. Either way, make sure your right sides are facing towards the right sides of your pillow front and your outer edges match.
IMG_1174
Pin around the edges well. Sew with a 1/4" inseam around the edges, backstitch over the envelope openings for extra strength. After the initial sewing I go around the edges with a serger, pinking shears or a quick zig zag stitch. Its especially important if you are using home weight fabric which tends to fray easily. Then clip your extra corner fabric off so the corners will turn nicely.
IMG_1180
Then turn it inside out and stuff a 16" pillow form in it.
Here are some pillow covers I previously made if you want more ideas and to see how it looks with the zig zag stitch around the pieces.
3427414485_c9a0e201f8_o
3428224034_df87731e28_o
Be sure to check out all the scrap busting ideas by clicking the button below. Here’s to saving scraps!
Source:cluckclucksew.com

0 comments:

Post a Comment

Note: Only a member of this blog may post a comment.